0531-68788899

修车知识

首页>>新闻中心>>修车知识>>车身车门凹进去一点怎么办呢
联系我们
济南润奥奥迪专修

联系人:王经理

电话:15066665099

网址:www.sdrunao.com

地址:济南市历城区花园东路与奥体西路交叉口往西200米

车身车门凹进去一点怎么办呢

来源:http://www.jnrunao.com/ 日期:2020-06-12 发布人:runao
我们日常驾车,难免会遇到磕磕碰碰,一辆新车没过多久就有疤痕,车身车门凹进去一点也是很正常,这种凹陷虽然远观不明显,但是近看还是很影响整辆车的美观。那么车身车门凹进去一点怎么办呢?下面我们来看一看车门凹陷修复方法。
In our daily driving, we will inevitably encounter bumps and bumps. A new car will have scars soon. It's normal that the car door is sunken. Although the sunken is not obvious in the far view, it still affects the beauty of the whole car in the near view. So what about a little bit of a dent in the car door? Let's take a look at the repair method of the door depression.
车门凹陷部位只要漆面不脱落、不掉漆,而且凹陷深度不是很深,那么我们可以通过工具来进行修复,尽量恢复到之前车身状态,并不需要去钣金和喷漆。听到这里,相信很多车主都会长舒一口气,毕竟钣金喷漆的价格和耗时都是相当夸张的。
As long as the paint surface of the car door does not fall off or fall off, and the depth of the dent is not very deep, we can repair it with professional tools, try to restore the car body to the previous state, without body and paint. Hearing this, I believe many car owners will be relieved. After all, the price and time-consuming of body and paint are quite exaggerated.
我们可以网上购买一套凹陷修复工具套装,价格不贵,几十块钱就有了。首先清洗干净凹陷部位,然后把专用胶装入胶枪,插上电源预热7分钟左右。接着选择合适的垫片,注意大的凹陷用大的垫片,垫片越大牵引力越大,然后用胶枪在垫片上均匀涂满溶胶,迅速贴入凹陷位置,轻轻压住直到专用胶贴固后松手。
We can buy a set of dents repair tool set online, the price is not expensive, tens of dollars. First, clean the concave part, then put the special glue into the glue gun, plug in the power supply and preheat for about 7 minutes. Then select the appropriate gasket, pay attention to the large gasket for the large depression, the larger the gasket, the greater the traction, and then use the glue gun to evenly coat the gasket with sol, quickly paste into the depression position, gently press until the special glue is firmly fixed and release.
将牵引桥中间的孔对准贴固后的垫片,把螺帽套进垫片螺丝杠上拧紧,然后一直拧转螺帽直到拉拔到凹陷修平为止。修复完成后,把工具拆下,然后把酒精喷洒在车身残胶上,用刮铲清理干净。
Align the hole in the middle of the traction axle with the fixed gasket, insert the nut onto the gasket screw rod and tighten it, and then screw the nut until it is drawn until the concave is flattened. After the repair is completed, remove the tools, spray the alcohol on the residual glue of the car body, and finally clean it with a spatula.
如果你不愿意亲自动手,那么我们可以交给外边的维修店,他们有一种叫做凹陷修复技术,也称为轻钣金,不过凹陷修复技术其实和我们自己动手差不多,都是采用吸盘吸出凹陷位置,然后借助钩子伸进凹陷区域背后,然后慢慢顶出来,用橡胶锤把突出来的部分进行处理。
If you don't want to do it yourself, we can give it to the outside repair shop. They have a kind of technology called dent repair, also known as light sheet metal. However, the dent repair technology is similar to our own, which uses suction cups to suck out the position of the dent, then extends into the back of the dent area with the help of hooks, then slowly ejects it, and finally uses a rubber hammer to put the protruding part out The treatment shall be carried out separately.
汽车凹陷修复技术根据凹陷修复难度和面积来决定价格,还有凹陷的尖锐程度,越尖锐的坑修复难度越大,价格也要几百元以上。例如一个鸡蛋形状大小的凹陷,价格一般要150元左右。
According to the difficulty and area of pit repair, the price of automobile pit repair technology is determined, as well as the sharpness of pit. The sharper the pit is, the more difficult it is to repair, and the price is more than several hundred yuan. For example, the price of a hollow egg is about 150 yuan.
车门凹陷看似很容易修复,随便拿东西拉拉或者从后面顶顶就能恢复,实际上有很大局限性,如果在车漆损伤情况下无法修复,如果凹陷位于轮眉、边角与AB柱附近,那么也不容易修复。
It seems that the car door depression is easy to repair. It can be recovered by pulling things at will or from the back roof. In fact, it has great limitations. If it cannot be repaired in case of paint damage, if the depression is located near the wheel arch, corner and ab column, it is not easy to repair.
此文关键词: 济南奥迪专修  

推荐阅读/ Recommended reading

轮胎磨损主要是轮胎与地面间滑动产生的磨擦力造成的。汽车起步、转弯及制动等行驶条件的不断变化,转弯速度过快、起步过急、制动过猛,轮胎的磨损就快。

安全气囊使用过程中需要的注意事项? 2020-07-31
汽车洗车需要注意的几个误区? 2020-07-20
汽车维修保养小窍门 2020-07-08
汽车轮胎的螺丝是按哪个方向拧? 2020-06-30

鲁公网安备 37010202001813号